/** | |
* \file | |
* | |
* \brief User Interface | |
* | |
* Copyright (C) 2009 Atmel Corporation. All rights reserved. | |
* | |
* \page License | |
* | |
* Redistribution and use in source and binary forms, with or without | |
* modification, are permitted provided that the following conditions are met: | |
* | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* | |
* 3. The name of Atmel may not be used to endorse or promote products derived | |
* from this software without specific prior written permission. | |
* | |
* 4. This software may only be redistributed and used in connection with an | |
* Atmel AVR product. | |
* | |
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED | |
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE | |
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR | |
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT | |
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY | |
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH | |
* DAMAGE. | |
*/ | |
#include "compiler.h" | |
#include "conf_usb.h" | |
#include "udc.h" | |
#include "udi_hid_generic.h" | |
#include "board.h" | |
#include "led.h" | |
#include "ui.h" | |
void ui_init(void) | |
{ | |
LED_On(LEDUSB_GPIO); | |
LED_On(LED0_GPIO); | |
LED_Off(LED1_GPIO); | |
LED_Off(LED4_GPIO); | |
LED_Off(LED5_GPIO); | |
LED_Off(LED6_GPIO); | |
LED_Off(LED7_GPIO); | |
} | |
void ui_powerdown(void) | |
{ | |
LED_Off(LED0_GPIO); | |
LED_Off(LED1_GPIO); | |
LED_Off(LED4_GPIO); | |
LED_Off(LED5_GPIO); | |
LED_Off(LED6_GPIO); | |
LED_Off(LED7_GPIO); | |
} | |
void ui_wakeup_enable(void) | |
{ | |
PORT_t *port; | |
// Configure pin change interrupt for asynch. wake-up on button pin. | |
ioport_configure_pin(GPIO_PUSH_BUTTON_0, | |
IOPORT_DIR_INPUT | IOPORT_PULL_UP); | |
port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0); | |
port->INT0MASK = 0xFF; | |
port->INTCTRL = PORT_INT0LVL_LO_gc; | |
} | |
void ui_wakeup_disable(void) | |
{ | |
PORT_t *port; | |
port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0); | |
port->INT0MASK = 0x00; | |
} | |
// Interrupt on "pin change" from switch to do wakeup on USB | |
// Note: | |
// This interrupt is enable when the USB host enable remotewakeup feature | |
// This interrupt wakeup the CPU if this one is in idle mode | |
ISR(PORTF_INT0_vect) | |
{ | |
PORT_t *port; | |
port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0); | |
port->INTFLAGS = 0x01; // Ack interrupt | |
// It is a wakeup then send wakeup USB | |
udc_wakeup(); | |
} | |
void ui_wakeup(void) | |
{ | |
LED_On(LED0_GPIO); | |
} | |
void ui_process(uint16_t framenumber) | |
{ | |
if ((framenumber % 1000) == 0) { | |
LED_On(LED1_GPIO); | |
} | |
if ((framenumber % 1000) == 500) { | |
LED_Off(LED1_GPIO); | |
} | |
} | |
void ui_led_on(uint8_t led_num) | |
{ | |
switch (led_num) { | |
case 1: | |
LED_On(LED4_GPIO); | |
break; | |
case 2: | |
LED_On(LED5_GPIO); | |
break; | |
case 3: | |
LED_On(LED6_GPIO); | |
break; | |
case 4: | |
LED_On(LED7_GPIO); | |
break; | |
} | |
} | |
void ui_led_off(uint8_t led_num) | |
{ | |
switch (led_num) { | |
case 1: | |
LED_Off(LED4_GPIO); | |
break; | |
case 2: | |
LED_Off(LED5_GPIO); | |
break; | |
case 3: | |
LED_Off(LED6_GPIO); | |
break; | |
case 4: | |
LED_Off(LED7_GPIO); | |
break; | |
} | |
} | |
bool ui_button(void) | |
{ | |
return gpio_pin_is_low(GPIO_PUSH_BUTTON_0); | |
} | |
/** | |
* \defgroup UI User Interface | |
* | |
* Human interface on Xplain-A1: | |
* - RED led close to USB connector is always on after firmware startup | |
* - Led 0 is on when USB line is in IDLE mode, and off in SUSPEND mode | |
* - Led 1 blinks when USB Host have checked and enabled HID generic interface | |
* - Led 4 to 7 are controlled by USB Host application | |
* - Switch 0 events are reported to USB Host application | |
* - Switch 0 can be used to wakeup USB Host in remote wakeup mode. | |
*/ |