| /** | |
| * \file | |
| * | |
| * \brief USB configuration file | |
| * | |
| * Copyright (C) 2009 Atmel Corporation. All rights reserved. | |
| * | |
| * \page License | |
| * | |
| * Redistribution and use in source and binary forms, with or without | |
| * modification, are permitted provided that the following conditions are met: | |
| * | |
| * 1. Redistributions of source code must retain the above copyright notice, | |
| * this list of conditions and the following disclaimer. | |
| * | |
| * 2. Redistributions in binary form must reproduce the above copyright notice, | |
| * this list of conditions and the following disclaimer in the documentation | |
| * and/or other materials provided with the distribution. | |
| * | |
| * 3. The name of Atmel may not be used to endorse or promote products derived | |
| * from this software without specific prior written permission. | |
| * | |
| * 4. This software may only be redistributed and used in connection with an | |
| * Atmel AVR product. | |
| * | |
| * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED | |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE | |
| * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR | |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
| * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
| * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT | |
| * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY | |
| * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH | |
| * DAMAGE. | |
| */ | |
| #ifndef _CONF_USB_H_ | |
| #define _CONF_USB_H_ | |
| #include "compiler.h" | |
| //! To reduce the code size, the interrupt register management from IAR is not used | |
| #if defined(__ICCAVR32__) | |
| # include "intc.h" | |
| # undef irq_register_handler | |
| # define irq_register_handler(func, int_num, int_lvl) \ | |
| INTC_register_interrupt(&func, int_num, \ | |
| TPASTE2(AVR32_INTC_INT, int_lvl)) | |
| # undef ISR | |
| # define ISR(func, int_grp, int_lvl) \ | |
| __interrupt static void func (void) | |
| #endif | |
| /** | |
| * USB Device Configuration | |
| * @{ | |
| */ | |
| //! Device definition (mandatory) | |
| #define USB_DEVICE_VENDOR_ID USB_VID_ATMEL | |
| #if UC3A0 || UC3A1 | |
| #define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_AT32UC3A | |
| #define USB_DEVICE_PRODUCT_NAME "DFU AT32UC3A" | |
| #elif UC3B | |
| #define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_AT32UC3B | |
| #define USB_DEVICE_PRODUCT_NAME "DFU AT32UC3B" | |
| #elif UC3A3 | |
| #define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_AT32UC3A3 | |
| #define USB_DEVICE_PRODUCT_NAME "DFU AT32UC3A3" | |
| #elif UC3C | |
| #define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_AT32UC3C | |
| #define USB_DEVICE_PRODUCT_NAME "DFU AT32UC3C" | |
| #elif UC3D | |
| #define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_ATUC3D | |
| #define USB_DEVICE_PRODUCT_NAME "DFU AT32UC3D" | |
| #else | |
| #error Unknow DFU PID for this AVR part | |
| #endif | |
| #define USB_DEVICE_MAJOR_VERSION (BOOTLOADER_VERSION>>4) | |
| #define USB_DEVICE_MINOR_VERSION (BOOTLOADER_VERSION&0x0F) | |
| #define USB_DEVICE_POWER 100 // Consumption on Vbus line (mA) | |
| #define USB_DEVICE_MANUFACTURE_NAME "ATMEL" | |
| #define USB_DEVICE_ATTR USB_CONFIG_ATTR_SELF_POWERED | |
| /** | |
| * Device speeds support | |
| * Only Full speed is authorized on DFU ATMEL | |
| * Because FLIP supports only full speed | |
| * Also: | |
| * - low speed is too slow (endpoint 8 Bytes) | |
| * - high speed does not increase flash program speed | |
| * - high speed is not supported on custom board with bad USB layout | |
| * @{ | |
| */ | |
| // No speed change possible | |
| //@} | |
| /** | |
| * USB Device Callbacks definitions (Optional) | |
| * @{ | |
| */ | |
| #define UDC_VBUS_EVENT(b_vbus_high) main_vbus_action(b_vbus_high) | |
| //@} | |
| //@} | |
| /** | |
| * USB Interface Configuration | |
| * @{ | |
| */ | |
| /** | |
| * Configuration of DFU interface | |
| * @{ | |
| */ | |
| //! Interface callback definition | |
| #define UDI_DFU_ENABLE_EXT() true | |
| #define UDI_DFU_DISABLE_EXT() | |
| //! Version of ATMEL protocol used | |
| #define UDI_DFU_ATMEL_PROTOCOL_VERSION DFU_ATMEL_PROTOCOL_VERSION_2 | |
| // Split erase is avaliable since batchisp 1.2.5 to avoid USB protocol 2 error | |
| #define UDI_DFU_ATMEL_PROTOCOL_2_SPLIT_ERASE_CHIP | |
| //@} | |
| //@} | |
| /** | |
| * USB Device Driver Configuration | |
| * @{ | |
| */ | |
| #define UDD_NO_SLEEP_MGR | |
| //@} | |
| //! The includes of classes and other headers must be done at the end of this file to avoid compile error | |
| #include "udi_dfu_atmel_conf.h" | |
| #include "main.h" | |
| #include "conf_isp.h" // Need to put bootloader version at USB device version | |
| #endif // _CONF_USB_H_ |